Exhibitors' products #SICAM2024

PROAQUA INVISIBLE TOUCH PRO4130XX

INTERIOR ZERO GLOSS 1-2K WATERBORNE SELF-SEALER

Ecological self-sealing lacquer for interiors.
Creates a 0-gloss natural effect comparable to raw wood. For this effect apply as a self-sealer in two coats with an intermediate sanding using 320 grit paper.
Due to waxes creates a very soft surface, that is pleasant to touch.
Scratch resistant, fast drying, resistant to yellowing, very transparent.
Ready-to-use, but can be catalized.

clear/ white

Main characteristics of the product:
- Untreated wood effect
- Scratch resistance
- Fast drying
- Good floating
- Resistance to yellowing
- High transparency

- Sheen level: 00-05 Gloss
- Brush, Roller, Spray gun (nozzle clear 1,4-1,8 mm, white 1,6-2,0 mm, pressure 4 bar)
- Viscosity Ford 4: 34 sec.
- Solid content: 30%
- Thickness: 80-120 gr/m2
- Sandable: 6 h
- Dust free: 30"
- Overcoatable: 6 h
- Complete drying: 18 h

Range of use:
Spray
Roller
Brush

Prodotti per il trattamento del legno

PROAQUA LASUR PRO3702XX

EXTERIOR DEEP-WETTING WATERBORNE CARPENTRY IMPREGNANT
Low viscosity, deep wetting, non film-forming semi-transparent stain. Recommended for artisanal and industrial cycles.
Iron oxides and UV filters protect wood lignin from decomposition. Special additives protect wood from molds and insects. Suitable for impregnating machines.
One coat is sufficient for interior application.

Main characteristics of the product:
- Great penetration
- Low viscosity
- Ready to use
- Light resistant colours
- Prevents the formation of chromophoric molds and the attack of lignivorous insects

- Brush, Roller, Flow Coating, Immersion
- Viscosity Ford 4: 15 sec.
- Solid content: 14%;
- Thickness: 80-120 gr/m2
- Overcoatable: 4-6 h

Prodotti per il trattamento del legno

PROAQUA PRIMER BASE COAT PRO8526BI

INTERIOR 1-2K HIGH BUILD WATERBORNE BASE COAT FOR FURNITURE WHITE
White basecoat for high-quality interior furniture. Suitable for artisanal and industrial cycles, for closed pore effect. Very flexible, non-yellowing and easily sandable.
Particulary indicated for MDF, walnut, fraké, ramin, tanganika, ayous etc. Ready-touse, but can be catalized. Suggested top coat: VM8524BI

Main characteristics of the product:
- Spray gun (nozzle 1,8-2,2 mm, pressure 4 bar)
- Viscosity Ford 8: 40"
- Solid content: 56%
- Thickness: 50-250 gr/m2
- Sandable: 6-8 h
- Overcoatable: the next day/

Prodotti per il trattamento del legno

PROAQUA TOP COAT PRO8524XX

INTERIOR WATERBORNE ACRYLIC TOP COAT FOR FURNITURE
CLEAR (TR)/WHITE (BI) Sheen level: 10-20, 30-40, 50-60, 80-90 gloss
Top coat for high-quality interior furniture and doors. Suitable for artisanal and industrial cycles, for open and closed pore effects.
Good surface resistance, good verticality, soft to the touch, resistance to yellowing, quick drying. Particulary recommended for oak, walnut, mahogany, ash, fraké, ramin etc.
Ready-to-use, but can be catalized. Suggested base coats: VM8523TR or VM8526BI.

Main characteristics of the product:
- Resistant to yellowing
- Low viscosity
- Ready to use
- Very easy to apply.
- Good vertical hold
- High softness to the touch
- Re-coatable

- Sheen level: 00-05, 10-20, 30-40, 50-60, 80-90 Gloss
- Brush, Roller, Spray gun (nozzle clear 1,4-1,8 mm, white 1,6-2,0 mm mm, pressure 4 bar)
- Viscosity Ford 4: 130-140″ clear., 180-220″ white
- Solid content: 31-42%
- Thickness: 100-120 gr/m2
- Dust free: 20"
- Complete drying: 24h

Range of use:
It is a general use product for the treatment of furniture and accessories, of horizontal as well as vertical surfaces, of assembled ones, as well as disassembled. To be used exclusively with a proper base coat.

Way of use:
spray gun
brush
Roller

Substrate preparation
Prepare the substrate through applying the HF8523 base coat.

Tips & tricks
To further improve performance, add CAH8506.XX, hardener for water-based lacquers in a proportion of 10: 1, mix well.

Prodotti per il trattamento del legno

Natural oil based treatment, reinforced with high quality resins, for the finishing of wood floors, with the application of one or two coatings. Suitable for soft and hard timbers, in particular for adsorbent and porous woods. The new Quick version offer a real fast drying. The addition of special waxes allows to obtain surfaces with a natural effect, with the same scratch resistance but with an higher softness to the touch and an increase in opacity. Usually opaque, can become a little glossy with more than one layer. White is excellent for oil finishes in which intense coloration and low oxidation over time is desired, transparent is ideal for protecting the white layer from scratches and dirt.

HARDWAX COLOROIL QUICK

Borma Wachs

Prodotti per il trattamento del legno

HARDWAX PARQUET OIL QUICK 1030

Borma Wachs

Prodotti per il trattamento del legno

A blend of valuable vegetable oils, reinforced with high quality resins, for the finishing of untreated interior wooden surfaces.
It provides an excellent resistance to stains and wear, does not need specific basecoats and is supplied ready for use.
Traditional fast drying, low viscosity formulation.

Recommendations for application:
The product can be applied by brush, roller, rag, spray or on industrial lines.
Always provide proper ventilation to the treated areas to allow the correct drying process of the oil.
Approx yield: 12-24 m²/Lt.

The sculptural design in the form of straight ribs and waves lends a third dimension to the design surface in concrete look. The 3D structure combines coolness and elegance. A product that meets the highest standards of individuality, aesthetics and design in interior finishing and furniture construction. imi-wave is available in different variations and designs. It is lightweight and easy to work with.

imi-wave consists largely of natural raw materials, so it fulfils the highest standards of sustainability and environmental compatibility and, depending on the composite material, can be disposed of with household waste. A wide range of ideas can be realised, individual wishes can be implemented and the product is also easy to work with.

Red Dot Award

imi-wave was honoured with the Red Dot award in the Red Dot Award: Product Design 2024.

Every year, the highly regarded Red Dot Award: Product Design honours products that impress with their exceptionally high design quality, making it one of the most prestigious design competitions in the world. The Red Dot Design Award looks back on almost 70 years of history: in 1955, a jury came together for the first time to assess the best designs of the time.

imi-wave

Imi Surface Design

Natural surfaces

CIRCULAR PANEL FOR WORKTOPS

GREENGRIDZ

Greengridz

Worktops

KWC BEVO E

KWC BEVO E
The KWC BEVO E has a fascinatingly sleek silhouette and beautiful transitions and is made of hygienic stainless steel. Its prominent design element is its characteristically asymmetrical spout. The double skin construction ensures extra safety in the spray head models. The structure helps prevent burns. However hot the water is, the KWC BEVO E remains cool on the outside.

Kitchen components

KWC BEVO E Lever mixer - Kitchen

10.531.103.700FL 125350

* Lever mixer
* Lever installation only possible on the right side
- Child safety: cold water flow in lever position towards the front
* TouchProtect - anti-scald protection thanks to the "double skin" principle
* Pull-out aerator

Kitchen components

KWC BISTRO E Lever mixer - Kitchen

KWC BISTRO E
Lever mixer - Kitchen
10.581.144.700FL 125696

* Lever mixer
* Suspension spring
* TouchProtect - anti-scald protection thanks to the "double skin" principle
* Intrinsically safe against backflow and cross flow
* Swivel spout

Kitchen components

KWC BISTRO E Lever mixer - Kitchen

KWC BISTRO E
Lever mixer - Kitchen
10.581.433.700FL 125694

* Lever mixer
* HighFlex patented spring hose technology
* Lever installation only possible on the right side
- Child safety: cold water flow in lever position towards the front
* TouchProtect - anti-scald protection thanks to the "double skin" principle

Kitchen components

KWC ERA Soap dispenser

KWC ERA
Soap dispenser
Z.538.038.700 538038

* Soap dispenser KWC ERA
* Easily refillable from top without disassembly
* Mounting hole size ø26 mm
* Scope of delivery:
- Pump
- Soap container, filling capacity 350 ml Z.538.053

Kitchen components

KWC ERA Lever mixer - Kitchen

KWC ERA
Lever mixer - Kitchen
10.392.323.700FL 124405

* Lever mixer
* 2-hole
* Lever installation possible on the right or left side
* TouchProtect - anti-scald protection thanks to the "double skin" principle
* Pull-out spray 360° turn - magnetic tight-fit holder

Kitchen components

KWC EVE Lever mixer - Kitchen - with LEDShine

KWC EVE
Lever mixer - Kitchen - with LEDShine
10.121.103.150FL 122168

* Lever mixer
* Lever installation possible on the right or left side
* TouchProtect - anti-scald protection thanks to the "double skin" principle
* Pull-out aerator covered
- Neoperl® Caché®

Kitchen components

KWC FIT Lever mixer - Kitchen

KWC FIT
Lever mixer - Kitchen
10.541.002.176FL 125577

* Lever mixer
* Lever installation only possible on the right side
- Child safety: cold water flow in lever position towards the front
* gap between wall and centre of mounting hole min. 25 mm
* Intrinsically safe against backflow
* Pull-out spray

Kitchen components

KWC FIT Lever mixer - Kitchen

KWC FIT
Lever mixer - Kitchen
10.541.012.000FL 125574

* Lever mixer
* Lever installation only possible on the right side
- Child safety: cold water flow in lever position towards the front
* gap between wall and centre of mounting hole min. 25 mm
* Swivel spout 150°
- Neoperl® Cascade® SLC

Kitchen components

KWC GASTRO E Lever mixer - Commercial kitchen

KWC GASTRO E
Lever mixer - Commercial kitchen
24.561.144.700FL 125567

* Lever mixer
* Suspension spring
* TouchProtect - anti-scald protection thanks to the "double skin" principle
* Intrinsically safe against backflow and cross flow
* Swivel spout

Kitchen components

KWC ONO Lever mixer - Kitchen

KWC ONO
Lever mixer - Kitchen
10.151.423.700FL 122252

* Lever mixer
* HighFlex patented spring hose technology
* Lever installation possible on the right or left side
* Surgical-grade hardened stainless steel lever
* TouchProtect - anti-scald protection thanks to the "double skin" principle

Kitchen components

KWC ZOE Lever mixer - Kitchen

KWC ZOE
Lever mixer - Kitchen
10.201.102.176FL 124349

* Lever mixer
* Lever installation only possible on the right side
- Child safety: cold water flow in lever position towards the front
* gap between wall and centre of mounting hole min. 42 mm
* TouchProtect - anti-scald protection thanks to the "double skin"

Kitchen components

If you are looking for something out of the ordinary, you will find it here. High-gloss films in a wide range of colours and with the best surface properties have been delighting our customers for decades.
Especially interesting - metallic effects in granite, anthracite and champagne metallic.

Senosan AM1800 TopX

Senosan GmbH

Foils

Senosan AM1800 TopMATT Antifingerprint

Senosan GmbH

Foils

Supermatt acryclic films with excellent anti-fingerprint properties

These new supermatt surfaces with anti-fingerprint effect offer
the same high quality surface features as high gloss furniture
films. They are the latest benchmark in the industry. Their scratch
and abrasion resistance is significantly higher than standard matt
surfaces.
Moreover, senosan® AM1800TopMatt AF is powerfully resistant
to chemicals - even suitable for laboratory use as it resists most
aggressive substances.

If you‘re looking for premium quality for your furniture or kitchen production - here it is. senosan® GLASS in high gloss and matt finish is available in 9 colours ex-stock.

Senosan GLASS

Senosan GmbH

Foils

CAD+T Design

Are you into 3D bespoke furniture and customized designs? We are too!

DESIGN CLASSIC
The CAD+T Design Classic module with a cabinet configurator allows you, to create even walls, windows and doors and make your designs more dynamic. Benefit from the automated layout generator and the ability to make changes
quickly. Once you have started to design, you will benefit from the interconnectiviy of all our software modules. So will the design be ready for visualisation as well as construction and shop floor drawings. The Design Classic module is based on AutoCAD®.

DESIGN PROFESSIONAL
Using the latest technology, the CAD+T Design Professional module allows you to plan with ready-made architectural components as well as fully parametric models. Furthermore, you are able to model special constructions and generate BIM data. Benefit from the advanced features of CAD+T Design Professional. This module is based on Autodesk® Revit®.

DESIGN Cloud
This cloud based application allows you to design and visualize from single parts to complete rooms. The articles you are working with, have their own rules and logic for configuration and placement. These can be taken directly from the CAD+T Configurator Professional. Benefit from an optimized user interface, high quality designs and the ability to work independently from any location 24/7.

Software solutions

CAD+T Visualize

Do you have a sense for the whole look & feel of awesome renderings?

VISUALIZE CLASSIC
The CAD+T Visualize Classic rendering module is the ideal entry into the world of photorealistic visualization. This allows you to achieve a professional presentation with high end renderings for your clients. With the live-sync function to CAD+T, drawings can be quickly imported and decorated with numerous effects and objects such as people, animals, plants and much more. Changes will be applied automatically.

VISUALIZE PROFESSIONAL
The CAD+T Visualize Professional module includes all functionalities of the Visualize Classic module and enables additional effects such as the aging of materials, water and glass combinations, sunlight reflections, grass and more. Furthermore, the Professional module supports VR data export.

Software solutions

CAD+T Engineer

Use our special CAD+T tools to improve your construction process.

ENGINEER CLASSIC
CAD+T Engineer Classic module is based on AutoCAD® including the same user interface to ensure fast learn-ability. Sections and details are automatically created as well as different views which increases the work speed especially for individual construction. The automatic hardware placement supports the user especially with bespoke engineered furniture. Import and adjust any items easily from our CAD+T Design Classic module or start from scratch with a 2D
drawing and get the 3D data automatically.

ENGINEER PROFESSIONAL
This is a 3D parametric construction module based on Inventor® which similar, to CAD+T Engineer Classic, gives you automatically your cutting list and CNC data. We have enhanced this module to also work for furniture engineering. Due to the 3D parametric you can easily change features without changing the basic construction. This add-on for Inventor® specifically includes special features like core material selection, edge function and surfaces for the furniture industry.

Software solutions

CAD+T Configurator

Automatically generate individual drawings out of the configuration!

CONFIGURATOR PROFESSIONAL
The CAD+T Configurator Professional is a cloud based application which is scaleable and supports installation on-premise or in the cloud. The advanced software architecture enables usage under complex conditions, with huge amounts of data and for handling special adjustments.

Software solutions

CAD+T CNC

Optimise your production workflow by creating CNC data automatically!

The CAD+T CAM interface is an intelligent connection to 3-5 axis CNC machinery for the individual production. We generate directly out of CAD+T Engineer Classic or Professional module CNC files which consider the geometry and material features of each part. The CAM system includes an intelligent work-on logic according to material, tools and production steps which increases the usage efficiency of the machine without the need of a specialized CAM operator.

NESTING
Efficient nesting starts with the software and it ends at the finished part which leads to a faster and more efficient material handling in the workflow. Free shaped parts are placed by considering the tools and capabilities of the machine. We achieve through the perfect placement of small parts between the different sized parts an optimized material usage.

5-AXIS SIMULTANEOUSLY
Inventor® CAM is a 2,5 to 5 axis CAM system which allows 4 and 5 axis simultaneous work-on. The data is generated from CAD+T Engineer Professional, and through this high performance software, perfectly prepared for further production steps. You can check with the preview simulation for any potential collision. Additionally it will also calculate the time for more complex CNC programs. The Fusion 360 ultimate is the cloud based solution for this.

Software solutions

CAD+T Web Solutions

Manage and expand your sales channels - CAD+T Web Solutions!

EOS DOCS
CAD+T EOS Docs is the perfect tool to store your data safely in the cloud. Your fi les (drawings) are backed up and versioned. Thereby you have access to all versions of your data. In addition, you can manage your sales orders, material masters, license access and your CAD system settings can also be organized via CAD+T EOS Docs. This is the perfect tool if you want to share data and licences with your team or freelancers independent of their work location.

E-COMMERCE
The CAD+T E-Commerce application can be used as a sales tool for your own sales team as well as an online store for your partners or directly by the end user. In connection with CAD+T EOS you can easily handle products, generate information at a single point and publish the data customised to each user. Choose from a wide range of options and increase your online sales volume!

Software solutions